Buying Guide
Mica Thickness Guide: 0.8 mm vs 1 mm Laminate and Where Each Fits
By Lucky Trading Company · Updated November 2026
When people ask for "mica", the first question from a seller is usually the thickness. It matters more than most buyers realise, because the right laminate for a vertical wardrobe shutter is not the right one for a kitchen counter. This guide explains the thicknesses you will commonly see and how to match them to the job.
What Laminate Is
Decorative laminate, called mica in the trade, is a thin sheet made by pressing layers of kraft paper and a printed decor sheet under heat and pressure. It is glued onto a base board such as plywood, block board or MDF. The base gives the strength and flatness. The laminate gives the colour, texture and surface protection.
Common Thicknesses
Decorative laminate is commonly sold in thicknesses such as 0.8 mm and 1 mm. Some brands also offer thicker grades for heavier wear. Exact ranges vary by brand, so ask what is available rather than assuming.
| Thickness | Where it is usually used |
|---|---|
| 0.8 mm | Vertical surfaces: wardrobe shutters, cabinet doors, side panels, wall paneling |
| 1 mm | Surfaces that take more contact: tabletops, shop counters, work surfaces, drawer fronts |
| Thicker grades | Heavy-use or high-impact areas, where the brand offers them |
As a rule, the more a surface is knocked, scratched or leaned on, the more a thicker laminate helps. A vertical shutter that only gets opened and closed does not need the same toughness as a counter.
Do Not Forget the Backer Laminate
If you laminate only the front of a board, the surface pulls the board toward that side as it ages, and the shutter bows. Carpenters balance this by gluing a cheaper balancing laminate on the reverse face. It does not need to match the front finish. It simply keeps the board flat. For shutters and wide panels this step is worth the small extra cost.
Finish Matters as Much as Thickness
- Gloss shows fingerprints and scratches more easily, so it suits low-touch panels.
- Matte and textured finishes hide marks and are better for frequently handled surfaces.
- Dark solid colours show dust and scuffs more than lighter woodgrain patterns.
Which Base Board to Use
- Plywood or block board for anything that carries weight or sees moisture.
- MDF for flat decorative panels where a very smooth surface helps. Avoid it in damp areas.
- Use a waterproof grade (BWR or BWP) behind laminate in kitchens and bathrooms. A laminated surface can still let water in at edges and cut-outs.
Edges and Joints
The laminate is only as good as its edges. Use matching edge banding, seal cut-outs around sinks and hobs, and avoid leaving any raw board visible. Most failures start at an exposed edge, not in the middle of the sheet.
Quick Buying Checklist
- Tell the seller where the laminate will go so you get the right thickness.
- Check the batch and shade across all sheets before you accept them, because colour can vary between batches.
- Order enough in one go. Matching a shade later can be difficult.
- Ask for the balancing laminate for the reverse side.
Read our mica and laminate buying guide for finishes in more detail, or message us on WhatsApp with your project and we will help you choose.
Frequently Asked Questions
What is the difference between 0.8 mm and 1 mm laminate?
The 1 mm laminate is a little tougher and is usually chosen for surfaces that get more contact, like tabletops and counters. The 0.8 mm laminate is commonly used for vertical surfaces such as wardrobe shutters.
Do I need laminate on the back of a shutter too?
Yes, a balancing laminate on the reverse face keeps the board flat. Laminating only the front can make the shutter bow over time.
Can I use laminate in a kitchen or bathroom?
Yes, but use a waterproof grade base board and seal all edges and cut-outs, because water usually enters through exposed edges.
Ready to buy?
Message Lucky Trading Company on WhatsApp for wholesale rates and honest advice on what to buy.
Ask on WhatsApp